This data pack provides detailed installation, configuration and operation information forthe 7600 HD/SD Embedder/Disembedder module as part of the Av
Remote/Local switch:Set to the mode you will be using.SDI In:Video green LED:ON indicates module is locked to avalid input signal.OFF indicates no val
Avenue PC Remote ConfigurationThe Avenue PC remote control menus for this module are illustrated and explained below.Refer to the 7600 Parameter Table
Use the Aud Mix A menu below to control the audio mixing and shuffling of InputChannels 1 through 4. Each output bus assignment will be indicated by a
For Channels 5 –8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to
Use the Aud Delay menu shown below to adjust the amount of audio delay on the output:• Bulk Delay – set the amount of bulk delay using the left and ri
Use the Aud In A menu shown on the next page adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Input – s
Use the Aud In B menu shown below to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Input – select th
Use the Aud Out menu shown below to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take place i
AVENUE TOUCH SCREEN REMOTE CONFIGURATIONAvenue Touch Screen remote control menus for this module are illustrated and explainedbelow. Refer to the 7600
7600 Avenue Touch Screen MenusThe Vid In menu below provides the following read-only status reports for the inputvideo:• Input – reports the type of v
MODULE OVERVIEWThe 7600 module is an eight channel audio embedder or disembedder for 1.5 Gb/s highdefinition or 601 serial digital video. Four AES por
Use the Aud Mix A menu below to control the audio mixing and shuffling of InputChannels 1 through 4. Each output bus assignment will be indicated by a
For Channels 5 –8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to
Use the Aud Delay menu shown below to adjust the amount of audio delay on the output:• Bulk Delay – set the amount of bulk delay using the left and ri
Use the Aud In A menu shown on the next page adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Input – s
Use the Aud In B menu shown below to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Input – select th
Use the Aud Out menu shown below to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take place i
The Memory menu allows you to save overall module setups to five memory registers asfollows:• Select Save (it will light red), then select one of the
TROUBLESHOOTINGTo aid in troubleshooting, the LED indicators can be easily monitored from the frontpanel of this module to show module status. If usin
WARRANTY AND FACTORY SERVICEWarrantyThis Module is covered by a five year limited warranty, as stated in the main Preface ofthis manual. If you requir
SPECIFICATIONS7600 HD/SD AMDSD Video Input SignalNumber OneSignal Type: Serial Digital (SMPTE 259M)Impedance: 75 Ω BNCReturn Loss: >15 dBMaximum Ca
Model 7600 HD/SD AMD7600-3The B disembedder will also produce two pairs of audio signals referred to as SDI 5/6 andSDI 7/8. In the B disembedder, the
Embedded InputsNumber Four AES Streams (from video input)Eight channels from any two of four groupsChannels: EightBit Depth: 20 or 24 bitAES/EBU Digit
Model 7600 HD/SD AMD7600-4APPLICATIONSThere are four basic modes for using the 7600 module. Each of the modes is describedhere.8 Channels AES Audio in
Embedded HD or SD In, Embedded HD or SD Out In this mode, embedded audio from the HD or SD input stream is disembedded, shuffledin the Audio Input Sel
INSTALLATIONPlug the 7600 module into any slot in the 1 RU or 3 RU frame and install the plasticoverlay provided onto the corresponding group of rear
Model 7600 HD/SD AMD7600-7Connect an HD or SD videosignal to the SDI In BNC.3 RU Backplane1 RU BackplaneConnect the SDI Out 1-4BNCs to the desired HD
MODULE CONFIGURATION AND CONTROLThe configuration parameters for each Avenue module must be selected after installation.This can be done remotely usin
Model 7600 HD/SD AMD7600-97600 Parameter TableCONTROL LOCAL REMOTE DEFAULTDEFAULTUSER LEVELStrip AudioOffOnOffOff AdminCh 1-8 In (level)0 dB –70 to +1
Comments to this Manuals